1.7 Unless otherwise cleared by ATC, the taxi routes for all aircraft(below ICAO code letter “E”) when the isolated parking position used are as follow :

1. Departure

RWY 24R : Apron → E1 → E → A3 → RWY 24R threshold

RWY 06L : Apron → E1 → B3 → RWY 06L turnpad → RWY 06L threshold




2. Arrival

RWY 24R : RWY 24R threshold → RWY 06L turnpad → B3 → E1 → Apron

RWY 06L : RWY 06L threshold → RWY 24R turnpad → A3 → E1 → Apron

1. Departure

   1. Unless otherwise instructed by ATC, aircraft are advised to taxi to holding point as follow.

      RWY	TAXI Procedure
      06L	Aircraft taxi to RWY 06L by using E2, E, D3.
      06R	Aircraft taxi to RWY 06R by using E2, E, D3, D2.
      24L	Aircraft taxi to RWY 24L by using E1, E, A3, A2.
      24R	Aircraft taxi to RWY 24R by using E1, E.

   2. RWY 06L holding position marking is located at 90 m from RWY centerline and RWY 24R holding position marking is located at 301 m from end of RWY on TWY E.

   3. If unable to follow the above taxiing routes, the pilot should notify it to ATC.

   4. All aircraft shall not enter the TWY A3 and RWY unless instructed by ATC.

   5. All aircraft shall not cross the runway unless instructed by ATC.

   6. Aircraft can be instructed to take variable taxi routes such as taxi down/back track on runway for traffic separation.

2. Arrival

   1. After landing, pilot must vacate runway after receiving instructions from ATC. Due to the operations of the helicopter's on taxiway E, It could not be possible to vacate runway via intermediate taxiway or it could be necessary to backtrack on the runway.

   2. After entering taxiway E, aircraft are advised to taxi using arrival routes.

      (Aerodrome regulations - 4. Arrival procedure - 4.2 Arrival routes)

   3. If unable to follow the above RWY vacating routes, the pilot should notify it to ATC.

1. Departure

   1. All aircraft taxiing to RWY 06L/24R and RWY 06R/24L should change radio frequency from GND(121.875) to TWR(118.7) when entering the designated TWY as follows - A3, B3, B4, C3, and D3.

2. Arrival

   1. All aircraft vacating RWY 06L/24R and RWY 06R/24L should change radio frequency from TWR(118.7) to GND(121.875) when entering designated TWY as follows - A3, B3, B4, C3, and D3.

Aircraft shall obtain ATC clearance from Cheong-Ju GND prior to push-back.

1. When a pilot is ready for start-up and pushback, the pilot shall contact Cheong-Ju GND and provide the following :

   1. Call sign

   2. Gate/Stand number

   3. Type of request, engine start

2. Unless there is any special situation, priority to make push back will be given to aircraft operators who requested first.

3. For safety reasons, ground crews must clear the equipment, vehicles and other obstacles before aircraft makes push back or start-up engine.

4. A pilot shall confirm with ground crews (Ground handler, aircraft maintenance) whether there is no hazard to the aircraft starting up. The pilot shall not ask Cheong-Ju GND for engine start-up and push back until its safety check-up is fully confirmed. If there is any elements posing a potential failure, the pilot shall ask Cheong-Ju GND for push back only. After moving and standing the aircraft at a safety area, the pilot can ask for engine start-up.

5. Delays on the aircraft's push-back may be expected in order to maintain the distance of taxiing or push-back of other aircraft.

6. Unless otherwise instructed, push-back procedures are as follows.

   Aircraft stands	RWY in use	Push-back Procedures	Phraseology
   1	-	The aircraft shall be pushed back to face E2.	Push back approved to face E2.
   2~12	06L/06R	The aircraft shall be pushed back to face E2.	Push back approved to face E2.
   2~12	24L/24R	The aircraft shall be pushed back to face E1.	Push back approved to face E1.
   13	-	The aircraft shall be pushed back to face E1.	Push back approved to face E1.

Unless otherwise instructed, aircraft shall follow the routes below.

3.4  De-icing Operations

1. De-icing pad located in TWY E1 is de-icing pad 1(below code letter “E” available), and the one located behind spot NR. 8 - 9 is de-icing pad 2(below code letter “D” available).

2. De-icing Pad Operation

   1. Aircraft operator has to notice to the ground operator when he/she wants to use de-icing pad.

   2. Ground operator must notify authorized person about various matters related to operation procedure.

   3. When using a de-icing pad, notify GND before push-back.

   4. De-icing sequence and pad can be changed due to ground operator or equipment.

3. De-icing Pad Movement

   Aircraft operator has to maintain a communication system which is connecting with de-icing working.

1. It is available to make intersection departure on RWY 06L/24R via B3/B4/C3.

2. Intersection departure is only available when requested by pilots.

3. The length of available RWY refers to RKTU AD 2.13 DECLARED DISTANCES.

4. When necessary, aircraft may obtain intersection departure clearance while taxiing.

1. ICAO code letter “F” aircraft are not able to take-off or land on RWY 06R/24L.

2. ICAO code letter “F” aircraft shall enter the apron via TWY B3, TWY E1 and shall not move via TWY B4, TWY E2.

3. After take off or landing of ICAO code letter “F” aircraft, take-off or landing of any other aircraft should be prohibited on RWY 06L/24R until RWY checking and removing FOD are finished.

4. Aircraft TOW and LDW for the usage of the alternate airport shall be restricted as follows.

   A/C TYPE	MTOW	LDW
   A380	400 ton	386 ton
   B747-8	353.8 ton	344.3 ton

5. When necessary for FOD prevention, Special take off precedures (A380 Flight crew operation manual) can be performed under the condition that the total width of RWY plus shoulder pavement has less than 58 m.

6. The standard taxi routes for ICAO code letter "F" aircraft are as follows. :

   1. Taxi-in Procedures

   
   

   2. Push-back Procedures

   
   

7. On the area of RWY, TWY B3, TWY E1 (including the curved part of TWY) and apron, ICAO code letter "F" aircraft should move at a speed of below 30 kt except for the departure maneuvering, which pilots should make his engines idle power, adjusting the speed only with operating brake system by inertia. Especially, A380 movement procedure is as follows. :

   A380 Landing maneuvering
   Section	Status of engine		Speed
   	No. 2 & 3	No. 1 & 4
   Runway maneuvering	Idle power	Idle power	- Below 30 kt
   Turning pad	Idle power	Idle power	- Maintain 5 kt - Below 30 kt (After turning)
   Taxiway/Apron	Idle power	Shut down	- 7~8 kt
   A380 Departure maneuvering
   Section	Status of engine		Speed
   	No. 2 & 3	No. 1 & 4
   Taxiway/Apron	Idle power	Idle power	- 7~8 kt
   Runway maneuvering	Idle power	Idle power	- Below 30 kt
   Turning pad	Idle power	Idle power	- Maintain 5 kt - Below 30 kt (after turning)

   ※ A380 Aircraft to be taxied with their engine thrust 4~6% (When turning, aircraft should keep 10% thrust using one outer engine of opposite turning direction).

1. General Conditions

   1. Helicopters using civil aprons for taking off or landing shall be made on TWY E.

      For helicopters with wheel-type landing gear, take-off/landing/taxiing shall be conducted on the runway only after obtaining the permission from the control tower.

   2. After take-off, aircraft shall depart the traffic pattern to the northwest and any aircraft which want to take-off and cross the RWY 06R/24L shall obtain the prior permission from the control tower.

   3. Traffic pattern altitude for helicopters is 1 000 ft except for B-412 helicopter and light aircraft.

2. Procedure for departing traffic pattern (refer to the diagram)

   1. RWY 24L/R in use

      1. For aircraft departing the traffic pattern to the north

         Turn right after take-off, then fly to the right side of Ochang at 1 000 ft with broadcasting the position in the blind. Fly to the right side of the National road 17 while keeping a sharp lookout for other aircraft entering or leaving Jincheon branch office, the Forest Government Information Agency(RKUJ, 360°R 6 NM) at or above 1 500 ft, then fly to the right of the Jincheon tunnel(Caution R-139) and after broadcasting the position in the blind over the Jincheon Interchange, depart to the destination.

      2. For aircraft departing the traffic pattern to the west

         After take-off, turn right and fly via OCHANG at 1 000 ft with broadcasting the position in the blind, then proceed to BYONGCHEN at 1 700 ft along the south of the National road 510, and after broadcasting the position in the blind over BYONGCHEN, depart to the destination.

      3. For aircraft departing the traffic pattern to the south

         1. Take-off for crossing the runway 06R/24L shall be allowed only after obtaining the permission from the control tower.

         2. After take-off, turn left after obtaining the permission from the control tower and proceed direct to "C" Point at 1 200 ft.

         3. After take-off, maintain at or below 500 ft until passing through the end of the runway, and turn left after obtaining the permission from the control tower, depart to the destination via MIWON at 2 500 ft.

         4. If no permission is obtained from the control tower, maintain at or below 500 ft until passing the end of the runway, and turn right, then fly along the right side of JUNGBU Expressway, and after broadcasting the position in the blind over "C" Point at 1 200 ft, depart to the destination.

      4. For aircraft departing the traffic pattern to the east

         After take-off, turn right and proceed to JEUNGPYEONG at 1 000 ft via 'Down Wind leg' and depart to the destination after broadcasting the position in the blind over JEUNGPYEONG; or

         After obtaining the permission from the control tower, cross the extended centerline of runway at or below 1 000 ft and depart to the destination.

   2. RWY 06L/R in use

      1. For aircraft departing the traffic pattern to the north

         After take-off, turn left and maintain at or below 1 000 ft. Fly via the right side of Jeungpyeong Interchange at 1 000 ft. Proceed to Jincheon Interchange at 1 500 ft Jungbu Expressway and depart to the destination after broadcasting the position in the blind over Jincheon Interchange.

      2. For aircraft departing the traffic pattern to the west

         After take-off, turn left and maintain at or below 800 ft. Fly via the right side of OCHANG at 1 000 ft along JUNGBU Expressway. and proceed to BUNGCHEON at 1 700 ft along the National road 510, and Depart to the destination after broadcasting the position in the blind over BUNGCHEON.

      3. For aircraft departing the traffic pattern to the south

         1. Take-off for crossing the runway 06R/24L shall be allowed only after obtaining the permission from the control tower.

         2. After take-off, maintain at or below 500 ft until passing through the end of the runway, and after obtaining the permission from the control tower, turn right and depart to the destination via MIWON at 2 500 ft.

         3. When departing the traffic pattern via "C" point, turn right after passing through the end of runway and proceed to "C" Point at 1 200 ft via Down wind and Depart to the destination after broadcasting the position in the blind over "C" Point.

         4. Flying directly over downtown and school areas of Byeongcheon, Miwon and Ochang is prohibited.

3. Procedure for entering traffic pattern

   1. For aircraft entering the traffic pattern from the southwest

      Request landing clearance at "C" point at 1 500 ft then along the Mihocheon and right side of the Jungbu Expressway. Maintain at or below 1 000 ft until passing runway extension line.

   2. For aircraft entering the traffic pattern from the west

      After broadcasting the position in the blind over the Mokcheon Interchange, fly to the right side of Byeongcheon(right side of National road 21), then request landing clearance at Byeongcheon at 2 500 ft. Fly along the north of National Road 510, proceed to Ochang at 1 000 ft and then enter the traffic pattern.

   3. For aircraft entering the traffic pattern from the north

      Request landing clearance at Jincheon Interchange at 2 000 ft after leaving Geumwang(RKUK) tower and enter the traffic pattern via the right side of Jeungpyeong Interchange at 1 000 ft. When using runway is 6, after leaving Jincheon Interchange fly to the left side of Jincheon tunnel(Caution R-139) then passing abeam Jincheon branch office, the Forest Government Information Agency(RKUJ, 360°R 6 NM) at or above 1 500 ft then proceed to Ochang at 1 000 ft and then enter the traffic pattern.

   4. For aircraft entering the traffic pattern from the east

      After broadcasting the position in the blind over Goesan, request landing clearance over Jeungpyeong at 1 000 ft, and enter the traffic pattern via Jeungpyeong Interchange at 1 000 ft.

   5. For aircraft entering the traffic pattern from the northeast

      After broadcasting the position in the blind over Eumseong, request landing clearance at Jeungpyeong at 1 000 ft, and enter the traffic pattern via Jeungpyeong Interchange at 1 000 ft.

      * Flying directly over downtown and school areas of Byeongcheon, Miwon and Ochang is prohibited.

   6. For aircraft entering the traffic pattern from the southeast

      Fly via Miwon at 2 500 ft and request landing clearance at Jeungpyeong at 1 000 ft, Enter the traffic pattern via Jeungpyeong Interchange at 1 000 ft.

   7. When RWY 06 R/L is in use, enter the traffic pattern by maintaining 1 000 ft over Ochang.

      VFR aircraft reporting points
      Jincheon IC	365209.70N 1272830.20E	"C"	363737.50N 1272259.60E
      Jeungpyeong	364640.00N 1273630.00E	Ochang	364434.03N 1272747.39E
      "D"	364546.75N 1272620.05E	Miwon	364305.06N 1273924.42E
      Byeongcheon	364546.75N 1271800.32E	Jeungpyeong IC	364621.81N 1273025.87E
      "O"	364851.41N 1272404.68E	"P"	364941.23N 1272957.93E

   
   

1. General Conditions

   1. Use the runway 06L/24R and parking shall be made on civil ramp.

   2. Unless otherwise cleared by ATC, Use TWY B3/B4/C3 for departing and after landing RWY.

   3. Use northern traffic pattern and maintain pattern altitude 1 200 ft(AMSL).

   4. Pattern Traffic is only allowed up to 3 flights.

   5. Flight plan must be submitted 17:00, one day before the flight.

2. Possible time for flight

   Light Aircraft flights allowed 0700~2300.

   1. Weekdays

      1. Setting Military jet aircraft’s flight time as a standard, flight for light aircraft is allowed 1 hour 30 minutes before the military jet aircraft’s flight, and 20 minutes after military jet aircraft’s flight during daytime.

         During nighttime, flight for light aircraft is allowed 1 hour before military jet aircraft’s flight and 20 minutes after military jet aircraft’s flight.

      2. During military helicopters operation time, light aircraft can't fly simultaneously.

   2. Weekends

      1. Take off and lading training(touch and go, low approach) for light aircraft is allowed for 3 times for each flight plan during listed time below.

         09:00~12:00, 13:00~17:00, 18:00~21:00

      2. Light aircraft departing to other airport or arriving from other airport can only depart before 09:00 and arrive after 21:00.

3. Procedure for departing(refer to the diagram)

   1. RWY 24R in use

      - Turn right in 1NM after take-off then direct to the destination via O point(2 500 ft). Turn left after take-off shall be allowed after obtaining the permission from the control tower.

   2. RWY 06L in use

      - Turn left in 1 NM after take-off then direct to the destination via P point(2 500 ft). Turn right after take-off shall be allowed after obtaining the permission from the control tower.

4. Procedure for landing(refer to the diagram)

   1. RWY 24R in use

      1. For entering from the north or northeast REPORT outside of 10 NM from the ARP Downwind enter via “P“ point(3 000 ft).

      2. For entering from the west or northwest REPORT outside of 10 NM from the ARP Downwind enter via “O“ point(3 000 ft).

      3. For entering from the south or east REPORT outside of 10 NM from the ARP before crossing the extended centerline of runway. Land via “O“ point(3 000 ft) or “P“ point(3 000 ft) or when traffic is no factor land via “O“ point(3 000 ft) or “P“ point(3 000 ft) after passing over the airport(4 500 ft).

      4. Follow traffic seperation and condition enter after holding at O point(3 000 ft) or P point(3 000 ft) or direct Downwind enter.

   2. RWY 06L in use

      1. For entering from the north or northeast REPORT outside of 10 NM from the ARP. Downwind 1 000 ft enter from O point(3 000 ft) or Downwind enter via “P“ point(3 000 ft) or “O“ point(3 000 ft)

      2. For entering from the west or northwest REPORT outside of 10 NM from the ARP. Downwind enter via “O“ point(3 000 ft).

      3. For entering from the south or east REPORT outside of 10 NM from the ARP before crossing the extended centerline of runway. Land via “O“ point(3 000 ft) or “P“ point(3 000 ft) or when traffic is no factor land via “O“ point(3 000 ft) or “P“ point(3 000 ft) after passing over the airport(4 500 ft).

      4. Follow traffic seperation and condition enter after holding at O point(3 000 ft) or P point(3 000 ft) or direct Downwind enter.

         
         

1. General

   1. No person may take off unless two-way radio communication can be maintained with the Air Traffic Control.

   2. On recognition of communication failure during flight, squawk 7600 and if necessary to ensure safe altitude, climb to Minimum Safe Altitude or above to maintain obstacle clearance. Then comply with following procedures

2. VFR condition

   If the failure occurs in VFR　conditions, or if VFR conditions are encountered after the failure, each pilot shall continue the flight under VFR and land as soon as practicable.

3. IFR condition

   If the failure occurs in IFR conditions, or if paragraph 2 of this section cannot be complied with, each pilot shall continue the flight according to the following.

   1. DEPARTURE

      1. Under Pilot Navigation

         RWY 24 in use

         1)  RNAV OLREG 1

         • Climb on 240° course to OLREG, then...via(transition) and maintain 6 000 ft.

           - GUKDO TRANSITION(OLREG 1, GUKDO) :...330° track to LAVAX, then via 060° track to TUTAE, then via 044° track to GUKDO.

           - OSPOT TRANSITION(OLREG 1, OSPOT) :...330° track to LAVAX, then via 035° track to OSPOT.

           - OLMEN TRANSITION(OLREG 1, OLMEN) :...291° track to OLMEN, cross OLMEN at or above 8 000 ft.

           - BITUX TRANSITION(OLREG 1, BITUX) :... 330° track to LAVAX, then via 060° track to PUGOX, then via 150° track to LEDUD, then via 164° track to BOEUN, then via 141° track to BITUX.

         RWY 06 in use

         1) RNAV BUKIL 1

         • Climb on 060° course to BUKIL, then... via(transition) and maintain 6 000 ft.

           - GUKDO TRANSITION(BUKIL 1, GUKDO) : ...007° track to GUKDO, cross GUKDO at or above 8 000 ft.

           - OSPOT TRANSITION(BUKIL 1, OSPOT) :...330° track to TUTAE, then via 252° track to OSPOT.

           - OLMEN/BULTI TRANSITION(BUKIL 1, OLMEN/BULTI) :...330° track to TUTAE, then via 240° track to OWING, then via 280° track to OLMEN/BULTI.

           - BITUX TRANSITION(BUKIL 1, BITUX) :...330° track to TUTAE, then via 240° track to OLDIX, then via 150° track to MIGUL, then via 141° track to BOEUN, then via 141° track to BITUX.

      2. Under Radar vectoring

         - Proceed with the route from the point of radio failure to the fix, route, or airway specified in vector clearance,

         - In the absence of an assigned route, proceed with the route that ATC has advised, which may be expected in a further clearance, or

         - In the absence of an assigned route or a route that ATC has advised, which may be expected in a further clearance, proceed with the route filed in the flight plan, and

         - Maintain minimum en-route altitude (MEA) or the altitude/flight level cleared in the last ATC clearance received, whichever is higher, for 5 minutes

         - Continue the flight with altitude, flight level filed in the flight plan.

   2. ARRIVAL

      RWY 24 in use

      1. VFR condition

         The aircraft shall maintain VFR　and make an approach to land at RWY 24 passing ICHG 7 DME FINAL.

      2. IFR condition

         The aircraft shall proceed to IKAPO IAF and execute ILS Y/Z RWY 24R or VOR RWY 24R or RNAV RWY 24R or LOC 24R APP.

      RWY 06 in use

      1. VFR condition

         The aircraft shall maintain VFR and make an approach to land at RWY 06 passing SAPUX 6 DME FINAL.

      2. IFR condition

         The aircraft shall proceed to JIKJI IAF and execute RNAV RWY 06L APCH.

1. VFR flight which has encountered radio communication failure shall

   1. Helicopter

      - SQ 7600, and

      - When able to see light gun signal from control TWR, follow that instruction.

      - If unable to see light gun signal from control TWR, hold over downwind until ETA or for 10 minutes, whichever is later, then

      - Land on RWY in use as filed, and take caution of landing and departing traffic.

2. Conventional flight

   - SQ 7600, and

   - When able to see light gun signal from control TWR, follow that instruction.

   - If unable to see light gun signal from control TWR, hold on downwind until ETA or for 10 minutes, whichever is later, then

   - Aircraft should land on RWY in use.

   - Pilot shall take caution of landing and departing traffic.